MSD Mitsubishi 4-Tower Coil

Flat Terminals
In stock
$110.00 $88.71

MSD offers these two 4-tower coils as replacements for a variety of years ranging from 1994-2003 on vehicles including Mitsubishis, Neons and oth­ers. The difference between the two coils is the wiring connector. Consult the photos to ensure that you receive the coil you need for your engine.

Estimate shipping rates: $ 166.78

Mitsubishi 4-Tower Coil



  • Direct performance replacement for Mitsubishi 2.0L from early 1996 to early 1999
  • Direct performance replacement for Dodge 2.0L from mid 1997 to 2002
  • 77:1 turns ratio and lower primary resistance produce high voltage output
  • Works with stock ignition as well as MSD Ignitions
  • Flat terminal connection only
  • CARB E.O. Approved
Coil Specs
Turns ratio: 77:1
Primary resistance: .51 OHMs
Secondary resistance: 12K OHMs
Inductance: 7mH
Maximum voltage: 36,000 Volts
Peak current: N/A
Spark duration: N/A
Weight: 1180g

Learn everything about ignitions


Since electricity is not something we can physically see, the ignition system of our cars sometimes holds a little mystery or suspicion in its operation. It's important to realize that electricity, especially in an automotive setting, is not magic. And it's also important to realize that the ignition is key to your engine's performance. Your engine's overall performance is counting on that spark for complete combustion. Once you have a better understanding on how the ignition works and what each component actually does, things will begin to all make sense – and you'll be able to build the right ignition for your engine. Key goals of the ignition system:

  • Produce and deliver a high-voltage spark from a low voltage supply source (the battery)
  • This spark must be distributed to each combustion chamber as the piston nears top dead center on the compression stroke of the piston
  • Control and even alter when the spark occurs in the cylinder to meet different engine demands
  • Deliver a spark that has enough voltage and energy to ensure combustion of the fuel mixture
  • Be able to reliably accomplish these goals throughout a variety of rpm, load, temperatures and conditions

Quick Overview

A typical (meaning stock) 12-volt automotive ignition system operates by taking in a low voltage with high current from the car's battery and changing it into a higher voltage with lower current to jump the spark plug gap to propagate combustion in the cylinder. This process of changing low voltage to high voltage, called induction, takes place in the coil. From there, the high voltage spark is transferred to the distributor and on to a spark plug wire which must deliver the spark to the cylinder that is coming up on the compression stroke.


Two Sides to Every Ignition

To help better understand the operation of the automotive ignition system, lets break the system into two sides: a primary side and a secondary side.

MSD Coil diagram

The Primary Side:

The best way to define the primary components is that they are the parts that deal with the low voltage from the battery (the 12-volt side). Note that all of these parts use conventional wiring, since they're carrying lower voltages (except the battery cables that connect to the starter and alternator). This includes the battery itself, the ignition switch, a switching device and the wiring that connects to the coil's negative and positive terminals. The coil works both sides of the fence since it is the point where the primary and secondary systems meet as it takes a high voltage in but sends out a high voltage spark.


The Secondary Side:

The spark plug wire that connects the coil to the center terminal of the distributor (called the coil wire) is where the secondary side of the ignition begins. In stock systems, there is generally anywhere from 10,000 – 20,000 volts bolting through this wire. This spark zips through the wire and transfers to the rotor tip and then jumps across a small gap to another cap terminal. From there it moves out of the cap, through a spark plug wire, and finally across the spark plug gap. It is important to note that these secondary components, the cap, rotor and wires, are maintenance parts. Depending on your use, they should be inspected at least once every cruise season and numerous times during a race system.


Ignition Maintenance

Even though we're dealing with electronics, it's important to inspect your ignition system. Remember that the ignition system, at least the high voltage side, requires maintenance. Over time, the rotor tip wears as does the carbon contact of the distributor cap. Spark plug wires also grow weary over time from delivering voltages that can range from 10,000 to 40,000 volts. Plus, your wires operate in a harsh, nasty environment with extreme heat cycles, moving parts, oils and fluids all working against them.

  • It is recommended to inspect the cap and rotor at least once a year. If you live in an area with high humidity, you may want to inspect it more often.
  • Visually inspect the cap and rotor for wear of the cap terminals and the rotor tip.
  • Look for traces of carbon tracks where spark scatter occurs.
  • Visually inspect the plug wires for burns or tears. Also, it is a good idea to periodically check the resistance of the wires so see if there is a wire with excessive resistance indicating a break in the conductor.

The Coil

If there is a single part of the ignition that can holds some mystery to its operation, it is the coil. In a stock ignition system, 12 – 14 volts are delivered to the coil via the positive and negative terminals. Within the wink of an eye, it sends and output of 15,000 volts or higher! But there is no slight-of-hand taking place here – it's all a carefully crafted lesson in electronics. And one that can be tuned to meet a variety of output requirements.

MSD Coil

A coil consists of two sets of windings made up of insulated wires that surround an iron or similar metal core. The primary windings are generally made up of several hundred turns of a heavy wire while the secondary set consists of a much smaller gauge wiring that makes up thousands of turns. Coil manufacturers use a ratio between the secondary and primary winding numbers as a specification such as 100:1, which would mean 100 secondary turns to every one of the primary. This is a commonly used specification you will see in the coil information given by many manufacturers.

In a typical factory-style inductive ignition, current from the battery flows through the thicker primary windings when the switching device (points or magnetic pickups) is closed. This creates a magnetic field that builds strength thanks to the help of the iron core.

When the switching device opens (the trigger signal) the flow of current is broken and this magnetic field collapses over to the thousands of secondary windings. During this collapse, the voltage is stepped up, creating the higher voltage that is required to jump the spark plug gap and ignite the air/fuel mixture. This process is called inductance.

When shopping for a coil, keep in mind that the windings, materials and resistances of the coils can be altered to design coils for the street or for racing ignitions. Also there are a variety of sizes and shapes available today. Most manufacturers will explain what application the coils are used for so you should have no trouble finding a coil for your application.

Distributor Operation

The distributor of a typical engine has a lot more responsibility than just distributing the spark to the correct cylinder (which in itself is a feat). It is also triggers the coil to release the high voltage, in many cases it turns the oil pump, it distributes the spark to eight different cylinders and it alters the timing of the system. The distributor could be the hardest working part of your ignition system and this is why it is important to ensure that your distributor is up to the task of delivering the performance and power that you expect from your engine.

MSD Cutawaydist

Distributors have changed over the years. From plastic to billet housing materials, trigger mechanisms, timing controls and other items have all been modified over the years, yet most models will perform some if not all of the following duties:

  • Distribute the spark to different cylinders
  • Trigger the secondary side of the ignition
  • Alter the ignition timing
  • Driving the oil pump

Most distributors are driven by the camshaft through gears with a one-to-one ratio. (This means the distributor turns at camshaft speed, or half of crank speed.) There are a two important parts attached to the shaft; a trigger wheel and the rotor. The trigger wheel will vary depending on the type of trigger being used, but you will notice that it will have a tooth, or lobe or space for each cylinder of the engine. The rotor delivers the high voltage from the coil to the correct cap terminal. When the coil fires, the voltage is transferred through the coil wire to the center terminal of the distributor cap. This terminal contacts the center of the rotor, moves across the rotor and jumps across a small gap to the spark plug terminal of the cap. All of this occurs in fractions of a second and thousands of times.


Common Firing Orders for Domestic Vehicles

Spark Plugs

The spark plug is the final step for the ignition process. All of the voltage and energy build up to make a final leap across the plug gap which initiates combustion of the fuel mixture.

Spark Plug Details

The spark travels through the plug wire terminal to the threaded tip of the plug's center terminal. This terminal reaches all the way through the ceramic shell of the plug and ends at the electrode. The electrode is centered in the plug with a gap between it and the tip of which is connected to the metal housing of the plug forming a ground to the engine. The voltage jumps this gap to reach ground, resulting in a spark that ignites the air/fuel mixture in the cylinder.

One physical adjustment you can make with most plugs is the distance of the spark plug gap. Opening the gap forces the coil to build up a higher voltage in order for the spark to jump the gap.

Too large of a gap will also put added pressure on the secondary side of the ignition system, resulting in shortening the life of the components. Too small of a gap can make life too easy on the ignition to the point where the resulting in a weak spark that may not be strong enough to create a full combustion cycle of the air/fuel mixture.

There are a variety of spark plugs available from simple to exotic designs. And of course each one has their own theories on why one is better than the other. There are platinum-tipped plugs, plugs with tiny electrodes, some with numerous electrodes, and more. There are also spark plugs called resistor plugs, non-resistor plugs, hot plugs, and cold plugs. It is best to follow your engine builder's recommendation for plugs, or to test and tune with gaps and different brands.

Spark Plug Wires

The spark plug wires are the arteries of the ignition system. They provide the all-important path that allows the spark to transfer from the distributor cap to the spark plugs. The importance of good quality spark plug wires cannot be stressed enough! Plug wires live in a nasty environment and deal with high heat, abrasion, and getting whipped around at high speeds. They also need to be able to deliver high levels of voltage, while suppressing electromagnetic interference (EMI), which is created when high voltage passes through a wire.

MSD Wire

EMI refers to electrical noise or interference. Not only can it be an annoying buzz through the radio, but it can also wreak havoc on other electronics such as the rev limiter, or even the ECU of a car equipped with an EFI system. Original equipment spark plug wires combat EMI by using a carbon core material that has a very high resistance to the flow of the spark energy. The aftermarket offers a variety of wire sets that offer much lower resistance to ensure the most spark possible reaches the plugs.

When you're shopping for wires, look for lower resistance (measured in ohms), but also look for good EMI suppression. Another area of importance in the spark plug wire is the crimp between the terminal and the wire. Poor crimps can contribute to intermittent performance, a dead cylinder, and other problems. Also pay attention to the spark plug wire boots, as they need to survive parked in close proximity to the exhaust manifolds where heat is at its most extreme.

Battery and Charging System

You can have the most powerful ignition available and tuned to perfection, but without a battery to fire things up, you'll be going no where. The battery is the main source of power for a performance ignition system, and you need to be sure that it's capable of having the juice you need get the engine fired up. Not to mention to supply the ignition with current and voltage created by the alternator.

There's more relying on the battery than just the ignition system. The starter is also pulling huge amounts of current to crank over your engine. Adding compression and big strokes adds to this demand as well. Also, any other electrical devices such as fans, pumps, motors, and even fuel injection controls all tap into the battery for voltage.

When looking for a batter, certainly look at the cold cranking amps (CCA) racing. Also look at the cycling, or recovery capabilities of the battery.

Alternators are used on all street cars and even on the majority of race engines (except purpose built drag cars for the most part). The alternator is responsible for producing the electricity that a car draws from the battery while it is running. The alternator generates an alternating current (AC) when it is turned by a belt and pulley system connected to the crankshaft. Inside the alternator, a rotor spins to create a magnetic field. This field is induced into the windings of a stator (around the rotor), and eventually makes its way to the battery as direct current (DC).

If you run a battery without a charging system, it is important that it's fully charged at the beginning of the race so it has the capacity to power all of your car's electrical needs through the finish line.

Capacitive Discharge Ignitions

The biggest downfall of the inductive ignition design is the storage and build-up of the voltage. It takes a certain amount of time, called dwell or coil saturation, for the coil to transform the lower battery voltage to the higher voltage required to jump the spark plug gap. This system works well for OEM and general use, but falls short when it comes to increased performance and high rpm. This can result in a low voltage spark output that may not be powerful enough to ignite the air/fuel mixture in the cylinder. This can result in a misfire and loss of power.

Capacitive discharge (CD) ignition controls are the most common upgrade when it comes to improving the output of the ignition. The biggest advantage is that they are able to produce higher voltages from idle to red-line rpm. This is because a CD ignition draws its voltage supply directly from the battery and incorporates a transformer that steps this voltage up to close to 500 volts in many systems. A capacitor in the ignition stores this high voltage and fires it all when the distributor triggers it.

Secondary Voltage

The one short coming of a CD ignition is that the spark has very short duration. This isn't a problem at higher rpm, but could be a lower rpm. However, engineers found that with the increased voltage and nearly instant recovery, the spark can be fired multiple times on the same cycle, hence multiple spark ignitions (or multi-strike, or second strike, etc…). At an idle there may be five or six sparks, and as rpm increases, the number of sparks decreases. Generally, most CD ignitions produce multiple sparks through about 3,000 rpm. Keep in mind that we're discussing cycles that occur within milli-seconds!

A lot of people look at CD ignitions as race-only pieces, but that is not the case. In fact, a lot of these ignitions are legal to install on pollution-controlled engines – and some are even legal to install on OBD-II equipped cars. Most ignition controls are nearly universal in their application, as they can be installed on most anything with a distributor. Of course, distributors haven't been used on newer vehicles for several years, but there are also ignitions and coils available for these distributorless systems as well. These will be discussed in later chapters as well.

The series of full-power sparks that most CD ignitions produce creates more heat in the cylinder, resulting in improved combustion of the air/fuel mixture. In most cases, the benefits include an improved idle, quick starts, crisp throttle response, and improved high-RPM performance. If you have an engine that burns a little oil, runs a touch on the rich side, or the like, a multiple sparking ignition, CD or inductive, could help overcome these performance issues. That is, until they can be remedied correctly.

Write Your Own Review
You're reviewing:MSD Mitsubishi 4-Tower Coil
Your Rating