Defi Advance A1 Tacho 80mm 11000RPM Gauge
If you are looking to rev high enough to blow the welds on that intake manifold, then monitor the action with the Defi Advance A1 Tachometer. This tachometer is 80MM in size and reads up to a whopping 11K RPM. This is a tachometer for those of you with big horsepower builds with large framed turbochargers, and stroker motors that rev to the moon. When operating, this tachometer lights up to a light blue and white finish. And when the vehicle is shut off, this gauge will come to a rest in a nice tinted finish. This tachometer will come with a signal wire to splice into your ECU.
Also included are the mounting hardware, and all the appropriate wiring to make this tachometer ready for installation.
Specifications
- Brand: Defi
- Backlight Color: White
- Gauge Face Color: Black
- Gauge Needle Color: White
- Gauge Range: 11,000rpm
- Gauge Size: 80mm
- Includes Sending Unit: No
Summary
Defi-Link Meter ADVANCE A1 is a series of gauges that need to be connected to the Defi-Link ADVANCE Control Unit.
ADVANCE A1 is a series of premium models that contain a metallic toned dial plate with convex scales. It also provides high visibility by using a low-reflection glass.
The numbers are not visible until the ignition is turned on.
- There are turbo 200kPa, turbo 300kPa, oil pressure, fuel pressure, oil temperature, water temperature, and exhaust temperature in 60mm gauges. In addition, there is an 80 mm tachometer
- The scales and pointer are white while the ignition is off. The numbers light up after ignition is turned on.
- A low-reflection glass provides high visibility.
- The metallic tone dial plate with concave scales and fine circular hairlines gives a premium texture.
- The mounting bracket fits in your dashboard and ADVANCE A1 by using the accessory cover.
- One ADVANCE Control Unit operates up to 7 gauges or displays in total.
- *Defi-Link ADVANCE Control Unit (sold separately) is necessary to operate A1 gauges.
- *Defi-Link Meter ADVANCE A1 is expressed as ADVANCE A1 or A1 gauges.
Main specifications, functions, and features
- ADVANCE System
- ADVANCE Control Unit necessary
- Commercial attachment necessary
- Stepping motor: STS26/VS2
- Illumination color: white
- Illumination ON/OFF: interlocked with vehicle illumination switch
- LED illumination
- Indicator output
- Built-in indicators
- Driving data can be recorded & replayed
- Opening mode/Ending mode
- Size: 60mm/80mm tachometer
- The applicable number of cylinders: 1, 2, 3, 4, 5, 6, and 8
- Mounting bracket and cover attached
Specifications
Size
60mm series
80mm Tachometer
Other specifications
| Power supply voltage |
Supplied from Defi-Link ADVANCE Control Unit |
| Current consumption | Maximum during 7 gauges are connected +B 2A(IGN ON), 5mA(IGN OFF) ILM 800mA |
| Illumination color | White The illumination color cannot be changed. Pointer: red Warning LED: red Peak LED: blue |
| Display range | Refer to lineup. |
| The applicable number of cylinders | 1,2,3,4,5,6,8 |
| Note |
*Products is for only on vehicles with a 12V electrical system. Never use products on 24V vehicles. |
ADVANCE System connection
The Defi-Link ADVANCE system allows gauges and displays to be attached to the ADVANCE control unit with a single “DAISY CHAIN” wiring system.
ADVANCE gauges, displays, and Control Unit are equipped with microcomputers. Distant gauges and displays can be operated at hand.
The system is also designed to allow all sensors to be attached to the ADVANCE control unit so that gauges and displays can be mounted separately without the need for multiple tubing or wiring to each gauge.
- *ADVANCE System (from 2009) and Defi-Link System (from 1998) are not compatible. Control unit and sensor wires for Defi-Link System cannot be used for ADVANCE System except some common sensors and extension wires.
- *To operate ADVANCE gauges and displays, ADVANCE Control Unit is necessary.
Wiring diagram
- ※One Control Unit can control up to 7 ADVANCE gauges & displays in all. (except DSDF)
- ※All the gauges(&displays) can be connected to both Meter Output connectors.
- ※Different color gauges can be connected.
- ※The same variety of gauges cannot be connected. (Ex. Two turbo gauges cannot be connected.)
- ※More than 2 Displays(ZDs) can be connected.
- ※Gauges(& displays) can be connected in any order.
- ※Smart Adapter and DSDF need to be connected to the end of the meter line because they have only one connector for meter wire.
