Defi Advance A1 Fuel Pressure Gauge 6Bar
The Defi Advance A1 Fuel Pressure Gauge is a great way to keep an eye on the welfare of your engine. If you should happen to have a sudden drop in fuel pressure then that could be an indicator of some serious engine problems and you can prevent any further damage by shutting the engine down and inspecting the culprit rather than further the potential harm by running the engine. The A1 Advance Series Gauges can collect data from the Defi Can Driver. However, there will be a sensor to provide readings.
This oil pressure gauge will read up to 10.0 KPA, and while the vehicle is operating it will illuminate to a bright white finish. And like most Defi gauges, it will come to a rest to a nice tinted finish when not operated. Included with the A1 Oil Pressure Gauge is the sensor, the required wiring, gauge cup, as well as miscellaneous hardware for installation. The sizing of this gauge is 60MM.
Specifications
- Brand: Defi
- Gauge Face Color: Black
- Gauge Needle Color: White
- Gauge Range: 0 Bar - 6 Bar
- Gauge Sending Unit: Electrical
- Gauge Size: 60mm
- Gauge Type: Fuel Pressure
- Requires Control Unit: Yes
- Sensor Thread Pitch: 1/8NPT
- Units: Imperial
Summary
Defi-Link Meter ADVANCE A1 is a series of gauges that need to be connected to the Defi-Link ADVANCE Control Unit.
ADVANCE A1 is a series of premium models that contain a metallic toned dial plate with convex scales. It also provides high visibility by using a low-reflection glass.
The numbers are not visible until the ignition is turned on.
- There are turbo 200kPa, turbo 300kPa, oil pressure, fuel pressure, oil temperature, water temperature, and exhaust temperature in 60mm gauges. In addition, there is an 80 mm tachometer
- The scales and pointer are white while the ignition is off. The numbers light up after ignition is turned on.
- A low-reflection glass provides high visibility.
- The metallic tone dial plate with concave scales and fine circular hairlines gives a premium texture.
- The mounting bracket fits in your dashboard and ADVANCE A1 by using the accessory cover.
- One ADVANCE Control Unit operates up to 7 gauges or displays in total.
- *Defi-Link ADVANCE Control Unit (sold separately) is necessary to operate A1 gauges.
- *Defi-Link Meter ADVANCE A1 is expressed as ADVANCE A1 or A1 gauges.
Main specifications, functions, and features
- ADVANCE System
- ADVANCE Control Unit necessary
- Commercial attachment necessary
- Stepping motor: STS26/VS2
- Illumination color: white
- Illumination ON/OFF: interlocked with vehicle illumination switch
- LED illumination
- Indicator output
- Built-in indicators
- Driving data can be recorded & replayed
- Opening mode/Ending mode
- Size: 60mm/80mm tachometer
- The applicable number of cylinders: 1, 2, 3, 4, 5, 6, and 8
- Mounting bracket and cover attached
Specifications
Size
60mm series
80mm Tachometer
Other specifications
| Power supply voltage |
Supplied from Defi-Link ADVANCE Control Unit |
| Current consumption | Maximum during 7 gauges are connected +B 2A(IGN ON), 5mA(IGN OFF) ILM 800mA |
| Illumination color | White The illumination color cannot be changed. Pointer: red Warning LED: red Peak LED: blue |
| Display range | Refer to lineup. |
| The applicable number of cylinders | 1,2,3,4,5,6,8 |
| Note |
*Products is for only on vehicles with a 12V electrical system. Never use products on 24V vehicles. |
ADVANCE System connection
The Defi-Link ADVANCE system allows gauges and displays to be attached to the ADVANCE control unit with a single “DAISY CHAIN” wiring system.
ADVANCE gauges, displays, and Control Unit are equipped with microcomputers. Distant gauges and displays can be operated at hand.
The system is also designed to allow all sensors to be attached to the ADVANCE control unit so that gauges and displays can be mounted separately without the need for multiple tubing or wiring to each gauge.
- *ADVANCE System (from 2009) and Defi-Link System (from 1998) are not compatible. Control unit and sensor wires for Defi-Link System cannot be used for ADVANCE System except some common sensors and extension wires.
- *To operate ADVANCE gauges and displays, ADVANCE Control Unit is necessary.
Wiring diagram
- ※One Control Unit can control up to 7 ADVANCE gauges & displays in all. (except DSDF)
- ※All the gauges(&displays) can be connected to both Meter Output connectors.
- ※Different color gauges can be connected.
- ※The same variety of gauges cannot be connected. (Ex. Two turbo gauges cannot be connected.)
- ※More than 2 Displays(ZDs) can be connected.
- ※Gauges(& displays) can be connected in any order.
- ※Smart Adapter and DSDF need to be connected to the end of the meter line because they have only one connector for meter wire.
