Defi Red Racer Volt Gauge 52mm 10 - 15V

On this page, you are looking at the Defi 52mm Red Racer Volt Gauge. The volt gauge is an excellent gauge you can have in your car as it can be used as a tool to measure your battery life, and it could be used as an indicator to check your alternator if your volts are below their normal measurement.

This gauge will read up to 15 volts, and it features high-brightness LEDs and will come with a self-diagnostic function that monitors both sensor disconnection and short-circuiting during the startup sequence.

Note that Defi Racer Series Gauges do not require the Defi-Link Control Unit II for use, and cannot be used in conjunction with it.

This gauge will come provided with a gauge cup, mounting hardware, and all the required wiring needed to make this gauge ready for the installation.

Specifications

Main specification

• Standalone
• Commercial attachment necessary
• Defi's unique STEP MASTER VS-2 stepping motor for the smoothest of operation
• Stepping motor:
  “STEP MASTER VS-2” for Φ52 and Φ60, and “STEP MASTER STS26A” for Φ80 provides smooth operation.
• Control unit NOT necessary/non-link system
• Illumination color: white/red/blue
• Opening mode/Ending mode
• LED illumination
• Illumination ON/OFF: interlocked with vehicle illumination switch
• Mounting bracket attached

Features 52mm & 60mm series

• Stepping motor "STEP MASTER VS-2" provides smooth operation.

• Ignition ON initiates self-luminescence gauge.

  Ignition off	Ignition on (Blue)	Ignition on (Red)	Ignition on (White)

• Illumination using high-brightness LEDs

• Lightning-like Opening / Closing mode

  Opening

  

   

  Closing
  

• Self-diagnostics function monitors both sensor disconnection and short-circuiting during startup.
  
• a) Sensor disconnection check
  This function reports any in-proper connections, broken or disconnected sensor or sensor wire. The pointer will wave between 250 and 260 degrees.
  b) Short-circuiting check
  This function indicates any short circuit on the sensor or sensor wire.
  The pointer will wave between 10 and 20 degrees.
• Full 270 degrees sweep dial provides ultimate visibility.
• A mounting bracket and instrument case is provided with the product.
• The red triangle of the regular position bezel can be used as a warning indicator and others.
• It does not require the Defi-Link Control Unit for use.

Features 80mm tachometer

• The maximum angle of deflective 270 degrees (full sweep) is controlled by the microcomputer up to 4600 division (0.057degrees each) to provide high precision in the accuracy of the information generated. The stepping motor is sufficient for the quick response of all sorts of professional motorsports.
• The gauge dial is invisible while the ignition switch is off. Once the ignition switch is turned on, a clear display appears by colored LED illumination. The gauge dial illumination and the red-emitting needle pointer provide high visibility.
  
  Ignition Off
  
  Red Racer Gauge
• The scale is compressed to acquire great visibility and ease of use.
  *Wide-angle scale is used at the idling range 0~3,000RPM.
  *The scale is fitted to recent engine power band and a linear scale is used from 3,000RPM to 11,000RPM.
• 
• The gauge dial and the needle pointer performs opening and closing modes interlocked with turning ON/OFF of the ignition.
• The maximum RPM during driving can be stored and checked later.
  
• There are 5 stages of brightness for the daytime and 6 stages for the nighttime. The brightness can be decreased/increased with the vehicle lights switched on/off.
• Two customer-defined warning RPMs can be set. When the RPMs are exceeded, the warning LED blinks/lights up and the warning buzzer sounds.
• The exclusive large-sized indicator which lights in green and red enhances the visibility of warnings in addition to the warning LED in the gauge.

   

  　　

• The large-sized switch unit with light is fixable on the gauge and is also detachable.

  　　

• Exclusive mounting band and back case
  The gauge is clinched by using the exclusive mounting band and back case. Wires can be stored in the back case neatly.

  

• Regular Position Bezel for 80mm (3 1/8") gauge is included in the product.
• *The illumination color can not be changed.

Specifications

2 1/16 & 2 3/8in(52&60mm) series

Power supply voltage	DC10 to 15V(Exclusive for 12V vehicle)
Current consumption	+B line: MAX 120mA (Dark current 0mA) IGN line: MAX 120mA ILM line: MAX 2mA
Dial color	Black (invisible until the ignition is turned on)
Illumination color	Blue, Red, White Pointer: Red, White *The color cannot be switched. *Refer to each lineup page.
Size
NOTE	*This product is for only on vehicles with a 12V electrical system. Never use this product on 24V vehicles. *Products can not be installed in altered vehicles. *Proper sensor attachments are necessary.

Racer Gauge connection

Wiring diagram

• *Sensors and sensor wires are common in those for ADVANCE System.
• *Control Unit is unnecessary to operate Racer Gauges. Racer Gauges cannot be linked to the ADVANCE System or Defi-Link system.

Lineup

Racer Gauges are available in Imperial units(PSI, deg F) and SI units(kPa, deg C).

White, red, and blue illumination colors are available. The illumination color cannot be switched.

Pictures may differ from the real products by processes and photography conditions, etc.