NOS Launcher Nitrous Controller

Overview

Nitrous Oxide Systems is proud to present the Launcher. It combines all the functions a nitrous racer could ever want into a single, easy–to–use controller. This handy device can be programmed to independently control up to 4 stages of nitrous from a laptop computer or via an available full color 3.5” LCD touch–screen. Easy to use graphical software makes the Launcher a breeze to program. The launcher is available in 3 basic configurations. It is available as the launcher controller only; the Launcher controller with 3.5” color LCD touch screen (Includes stylus and mini SD card for data–logging); or the Launcher controller with the handheld tuner for data–logging and quick changes in the staging lanes.
Nitrous control has just been taken to the next level!

Features

• Fully Programmable via laptop
• Compatible with Windows 2000, ME, XP, and Vista
• NEW innovative NOSbus 2-wire network interface for seamless integration with other Holley/NOS supported products.
• Easy to use graphical software
• Free software and firmware updates updatable by the user, downloadable off i-net.
• Available with a Handheld controller with SD card slot and USB interface for quick changes in the staging lanes and data-logging without laptop in the vehicle.
• Available with a 3.5” color, touch screen LCD for the ultimate in programming and looks. (No laptop Required)
• 3.5” Color, touch screen LCD also features a SD card slot for saving configuration files and data-logging as well as a USB interface.
• Full data-logging capability for easy reviewing of past runs through laptop, handheld controller (SD card) or LCD touch screen (SD card).
• Ability to save configuration files for easy set-up at different tracks or for weather conditions.
• Handheld controller or LCD touch screen allows changes in the staging lanes without laptop.
• Fully programmable 2 stages of nitrous control and with the optional slave controller you can add two more stages for a total of 4 fully programmable stages of nitrous control.
• Can be programmed to add or take away nitrous at any point to compensate for track or weather conditions.
• Integrated TPS for use on fuel injected or drive by wire vehicles without the need of a separate WOT switch.
• Two programmable activation inputs.
• Activation of nitrous can be provided from a power input, ground input, or a Falling or Rising TPS signal.
• Features an internal MAP sensor for nitrous ramps based on boost PSI.
• Solenoid control channels with a load capacity of 40 amps for use with large solenoids.
• 1st gear lockout to prevent the nitrous from being triggered until the RPM cutoff has been hit the first time.
• Two 1 amp general purpose outputs for timing retards, purge, or any activation switch (two additional on the optional slave controller).
• Use WBO2 controller p/n 15979NOS for rich or lean nitrous cut off. Requires Holley WBO2 sensors p/n 534-198 Bosch or p/n 534-194 NTK (NTK requires a 534-199 extension harness).
• Customer has the option to enable lean and/or rich nitrous cutoff with a programmable delay time up to 1 second. Richest/Leanest AFR data is also logged along with the nitrous data for advanced analysis.
• Pause Enable Option - when retriggered, (pedaling event) the ramp will continue where it left off (rather than starting over from scratch).
• Nitrous pressure sensor input for data-logging.
• PROGRESSIVE RAMP FEATURES
• RPM based - Programmable Trigger and End RPM points. Adjustable from 0-20,000 RPM
• Time Based - Programmable RPM trigger set point, Programmable Delay time and Ramp time, Adjustable from 0-10 seconds
• MAP (boost) based - Programmable RPM trigger set point, Programmable MAP trigger and MAP End points, Adjustable from -14.7 to 85 PSI
• Nitrous percentage - Programmable start and final percentages, Adjustable from 0 to 100%
• Safety features include - Rich or lean cutoff based off of A/F ratios, Nitrous pressure when using a nitrous pressure sensor, MAP (boost) pressure cutoff, RPM cutoff

Specs