Defi Advance A1 Tacho 80mm 11000RPM Gauge

Defi-Link Meter ADVANCE A1 is a series of gauges that need to be connected to the Defi-Link ADVANCE Control Unit.

ADVANCE A1 is a series of premium models that contain a metallic toned dial plate with convex scales. It also provides high visibility by using a low-reflection glass.

The numbers are not visible until the ignition is turned on.

• There are turbo 200kPa, turbo 300kPa, oil pressure, fuel pressure, oil temperature, water temperature, and exhaust temperature in 60mm gauges. In addition, there is an 80 mm tachometer
• The scales and pointer are white while the ignition is off. The numbers light up after ignition is turned on.
  
• A low-reflection glass provides high visibility.
  
• The metallic tone dial plate with concave scales and fine circular hairlines gives a premium texture.
  
• The mounting bracket fits in your dashboard and ADVANCE A1 by using the accessory cover.
  

• One ADVANCE Control Unit operates up to 7 gauges or displays in total.

• *Defi-Link ADVANCE Control Unit (sold separately) is necessary to operate A1 gauges.
• *Defi-Link Meter ADVANCE A1 is expressed as ADVANCE A1 or A1 gauges.

Main specifications, functions, and features

• ADVANCE System
• ADVANCE Control Unit necessary
• Commercial attachment necessary
• Stepping motor: STS26/VS2
• Illumination color: white
• Illumination ON/OFF: interlocked with vehicle illumination switch
• LED illumination
• Indicator output
• Built-in indicators
• Driving data can be recorded & replayed
• Opening mode/Ending mode
• Size: 60mm/80mm tachometer
• The applicable number of cylinders: 1, 2, 3, 4, 5, 6, and 8
• Mounting bracket and cover attached

Specifications

Size

60mm series

80mm Tachometer

Other specifications

Power supply voltage	Supplied from Defi-Link ADVANCE Control Unit
Current consumption	Maximum during 7 gauges are connected +B 2A(IGN ON), 5mA(IGN OFF) ILM 800mA
Illumination color	White The illumination color cannot be changed. Pointer: red Warning LED: red Peak LED: blue
Display range	Refer to lineup.
The applicable number of cylinders	1,2,3,4,5,6,8
Note	*Products is for only on vehicles with a 12V electrical system. Never use products on 24V vehicles. *Products can not be installed in altered vehicles. *To install pressure gauges or temperature gauges, proper sensor attachments are necessary. The thread sizes of sensors are 1/8PT.

ADVANCE　System connection

The Defi-Link ADVANCE system allows gauges and displays to be attached to the ADVANCE control unit with a single “DAISY CHAIN” wiring system.
ADVANCE gauges, displays, and Control Unit are equipped with microcomputers. Distant gauges and displays can be operated at hand.

The system is also designed to allow all sensors to be attached to the ADVANCE control unit so that gauges and displays can be mounted separately without the need for multiple tubing or wiring to each gauge.

• *ADVANCE System (from 2009) and Defi-Link System (from 1998) are not compatible. Control unit and sensor wires for Defi-Link System cannot be used for ADVANCE System except some common sensors and extension wires.
• *To operate ADVANCE gauges and displays, ADVANCE Control Unit is necessary.

Wiring diagram

• ※One Control Unit can control up to 7 ADVANCE gauges & displays in all. (except DSDF)
• ※All the gauges(&displays) can be connected to both Meter Output connectors.
• ※Different color gauges can be connected.
• ※The same variety of gauges cannot be connected. (Ex. Two turbo gauges cannot be connected.)
• ※More than 2 Displays(ZDs) can be connected.
• ※Gauges(& displays) can be connected in any order.
• ※Smart Adapter and DSDF need to be connected to the end of the meter line because they have only one connector for meter wire.