AEM Infinity-506/508 Plug and Play Jumper Harness for VW 1.8T 20VT
OVERVIEW
Complete Stand Alone Engine Control.
The Infinity ECU combines with the Plug & Play harness to replace the factory ECU. It controls all of the engine functions and the Plug & Play wiring harness adapter eliminates the need for cutting and splicing wires.
Plug & Play Harness with Expansion Port.
AEM’s sealed, weatherproof Plug & Play harness (sold separately) includes dual Lambda connectors, an AEMnet connector for communication with other AEMnet enabled devices and an auxiliary connector with a Deutsch DTM 12P connector for adding common aftermarket sensors including fuel pressure, air inlet temperature, MAP, boost control solenoid and ethanol content. The expansion port also includes a sensor ground, 5v reference, power from relay and high side output for activating a solenoid, and switched inputs for auxiliary radiator fan, boost target and no-lift shift.
FEATURES
Speed Density Fueling Control
The Infinity ECU does not support the factory Mass Airflow sensor. AEM offers a MAP sensor adapter harness (PN 30-3903-00) for seamless integration that provides speed density fueling control and allows users to eliminate the factory Mass Airflow sensor (MAF).
Uses Factory Wideband UEGO Air/Fuel Sensors & Boost Control Solenoid
The Infinity 1.8T Plug & Play Adapter Harness is designed to accept the factory wideband UEGO sensor, eliminating the need to add a wideband sensor to the car. The factory N75 boost control valve is supported, and the Infinity can control aftermarket boost control solenoids if added.
Full Drive-by-Wire Control
The Infinity programmable ECU for the VW 1.8T supports the factory Drive-by-Wire throttle body and can easily accommodate larger DBW throttle bodies using the DBW Set Up Wizard in InfinityTuner software.
CAN Integration
The Infinity standalone ECU features CAN integration on the MKIV 1.8T and retains dashboard functionality. Users can also view and log wheel speed and steering angle through the CAN datastream.
Traction Control
Traction control is fully tunable using the CAN based factory wheel speed sensors.
User Definable DBW Throttle Response
Users can define throttle curves in the InfinityTuner DBW software and take full control of throttle response. This allows users to change throttle response rate on the fly via an AEM 12-Position Trim Pot and is ideal for setting rain mode throttle curves.
200MHz Processor and Real Time Operating System
Late model vehicle ECU’s all run on faster processors. The Infinity ECU is built around a latest-generation 32 bit floating point 200MHz automotive processor and Real Time Operating System (RTOS), which is capable of processing 400 MIPS (millions of instructions per second). By comparison, common competitive systems typically use 20MHz to 50MHz processors. To our knowledge, the Infinity ECU currently has the fastest processing speed of any aftermarket Motorsports ECU available. This allows the Infinity to do more, faster, in a more stable programming environment.
- The Infinity’s 200MHz processor and RTOS makes the Infinity more responsive, for a better driving experience
- The Infinity’s 200MHz processor and RTOS allows for more accurate ignition timing, which enables an engine to create more power
- The Infinity’s faster processor allows it to perform more computational features with no sacrifice in processing performance
- The Infinity’s RTOS ensures strategic processing with optimized load balancing. This means that tuning one feature will not affect the performance of another feature
- Airflow model based (VE) tuning
- ECU Set Up Wizard simplifies start up
- Flex fuel compatible
- Multi fuel capable
- Programmable Drive by wire
- Multiple boost control strategies
- Nitrous control
- Map switching
- Single internal Lambda controller
- Dual knock sensing circuits
- Data logging up to 64GB, up to 100 channels at 1KHz
- Outputs to 3rd party dashes and data loggers
- Industry leading data transfer speed (up to 480Mb/sec)
- Integrated engine protection strategies
- Sealed enclosure and IP67 rated comms ports
CAPABILITY
AIRFLOW MODEL BASED CALCULATIONS
Infinity’s airflow model based systems greatly reduce the amount of time it takes to set up and tune an engine by eliminating many of the lookup and trim tables (correction tables) necessary in previous generation ECUs. The Infinity’s airflow based, or volumetric efficiency (VE) based models calculate an engine’s requirements in real time based on an advanced algorithm that has various modes for calculating air flow. Once the user inputs an engine’s basic parameters (displacement, cylinders, ignition type, and firing order) and methods of calculation for airflow and ignition they can begin setting the engine’s VE table in the software.
InfinityTuner USER INTERFACE SOFTWARE
InfinityTuner is optimized for speed and performance. The software has the power to control a multitude of features found in today’s modern racecars, and features an advanced tuning Wizard to reduce set up time. An ECU Setup Wizard takes complex calibration setup work and simplifies it through a smart interface that features tabs for quick set up of vital engine functions. Each tab includes a description of the function.InfinityTuner software is highly flexible. It allows you to choose from multiple strategies for boost control, idle control, traction control, charge air temp blend, launch control and more.All controls in the Infinity ECU are synched to logged data which allows users to edit calibration data during log playback to minimize tuning time. AEMdata, AEM’s advanced data logging analysis software is also included for reviewing data logs.
ULTRA-HIGH RESOLUTION FUEL CONTROL
The Infinity ECU calculates injector pulsewidth in units of 1/10th of a microsecond (0.0000001 second). Individual cylinder fuel trim is included and user adjustable.
ACCURATE IGNITION TIMING UNDER ANY CONDITION
InfinityTuner software features a 3D ignition trim map (coolant and air temp based), and its back-end timing code is tested to 100,000 RPM. Individual cylinder ignition trim is included.
FLEX FUEL COMPENSATION
Flex fuel compatibility is included, and the Infinity is able to make automatic adjustments for ethanol content in the fuel with the addition of an ethanol content sensor (sold separately).
MULTI-FUEL CAPABLE
The Infinity has the ability to run two separate fuel types simultaneously through staged fuel injection
DRIVE BY WIRE CAPABILITY
The Infinity-708/710 ECU can control drive by wire throttle bodies and includes auto calibration for DBW sensors. It includes idle control, an optional drive by wire rev limiter (for use as a launch limiter, holding limiter or in conjunction with other rev limiters) and necessary failsafes based on redundant sensor inputs. Traction control via drive by wire will be added in the future at no additional cost for existing Infinity ECU owners.
IDLE CONTROL
The Infinity ECU uses a coolant temp based idle control model. It includes an RPM vs. Engine Speed Rate idle decel feature that provides accurate control of the IAC and allows for adjustment of engine braking. The Infinity’s idle TPS offset provides smoother low idle operation when necessary, like driving in the pits or return lane following a pass.
MULTIPLE BOOST CONTROL STRATEGIES
Choose from time, gear, vehicle speed, switch based or other boost control strategies. The Infinity’s boost control includes two 2D base duty tables and two 2D boost target tables. The second tables can be used as a trim, and users can choose from multiple strategies including IAT, MAP, Baro (kpa), throttle %, flex fuel content, boost target and more. Please visit our Forumfor an in depth review of the Infinity’s boost control capabilities.
NITROUS CONTROL
The Infinity’s software allows you to run a single-stage wet or dry nitrous set up (four-stage available soon). This feature includes nitrous timing delay to account for nitrous bleed out, and can be set up for water/methanol injection tuning. Four stage nitrous will be upgraded for free for existing Infinity users when it becomes available.
VARIABLE VALVE CAM CONTROL
Set base duty, limit and VVC cam target for up to four cams through the InfinityTuner Wizard. Users are able to achieve a VVC cam target by setting Cam 1 base timing and base duty cycle % in a 2D table, and the software features a 1D base duty % table that controls the base duty cycle for the VVC output, which is tunable based on the VVC target.
MAP SWITCHING
The Infinity includes up to four separate ignition maps, four separate Lambda maps and two separate VE maps with independent values. Using AEM’s 12 Position Trim Pot, this powerful feature delivers many valuable tuning options including:
- Multiple maps for multiple track conditions (practice map, rain map, qualifying map, FTW map)
- Change boost target
- Change Lambda target
- Change ignition target
- Tie boost, Lambda and ignition targets together and change them all
- Ideal for test mapping during tuning
- Change boost base duty
- Control PWM switches (like water/methanol injection)
- Choose between 2 VE tables for VVC or when restrictors are in place
- Blend between flex fuel ignition maps
- Blend by cam position and gear
ENGINE PROTECTION
Multiple engine protection strategies are incorporated into the Infinity ECU. Available strategies include:
- MAP (create limp mode using Assumed Pressure Ratio table to compensate for pressure if sensor fails)
- Overboost (boost fuel cut until boost/throttle decreases)
- Fuel pressure (injector flow compensated for variations in pressure, sensor required)
- Oil pressure (trigger light or limit RPM if pressure drops below set value, sensor required)
- RPM (rev limiter)
- Coolant temperature, Temp vs. RPM (fuel and ignition cut, sensor required)
- Knock control with feedback
- Lean protection (fuel and ignition cut)
REAL-TIME ADVANCED DIAGNOSTICS
The Infinity’s diagnostics software can be configured to constantly monitor signal and current quality to alert the user of a potential issue before it creates the potential for engine damage.
INTERNAL WIDEBAND CONTROLLER
Dual Bosch wideband controllers are built into Infinity-708/710/712 ECUs. This provides highly accurate closed-loop AFR targeting and enables the sensor diagnostics in the ECU to determine the operational condition of the sensor.
LIGHTNING-FAST DATA LOGGING
Infinity’s logging feature supports 2 different file systems. A custom file system option will support 100 channels at up to 1 KHz using a high performance USB flash drive (sold separately). A standard FAT file system will support 10 channels at up to 1KHz, 20 channels at up to 500Hz or 100 channels at up to 200Hz. The Infinity includes a 4GB USB memory stick and the user can replace this with up to 64GB. Additionally, the user can also log direct to the PC at up to 500Hz when connected.
AEMdata DATA ANALYSIS SOFTWARE
AEMdataprovides an advanced interface for viewing the log files generated by the Infinity ECU.
DUAL KNOCK SENSING
Dual knock signal conditioning circuits allow for precise measurements of knock levels. The Infinity can utilize both Piezoelectric and Flat Response type knock sensors.
RELIABILITY
The Infinity ECU is constructed using automotive-rated components designed to withstand the harshest racing environments. Its enclosure and connectors are sealed to make it suitable for engine bay mounting. An advanced wear-leveling strategy for flash memory ensures a lifetime of reliable performance.
COMMUNICATIONS
The Infinity ECU is able to transfer data via USB at up to 480 Mb/second. It features a fully-sealed IP67 communications connection system.
SPECIFICATIONS
Click on the link for a PDF specifications sheet for all Infinity ECUs: Infinity ECU Specifications
SPECIFICATIONS
|
INFINITY-506
PN: 30-7106 |
INFINITY-508
PN: 30-7108 |
2-Stroke Engines
|
Yes
|
Yes
|
4-Stroke Engines
|
Yes
|
Yes
|
Cylinders
|
Up to 6
|
Up to 8
|
High Impedence Injectors (Sequential)
|
Up to 6
|
Up to 8
|
Low Impedence Injectors (Sequential)
|
Up to 6
|
N/A
|
Coils (0-5V Falling Edge)
|
Up to 6
|
Up to 8
|
Digital Inputs
|
Up to 6
|
Up to 6
|
VR/Mag Inputs
|
Up to 4
|
Up to 4
|
Analog Voltage Inputs
|
Up to 9
|
Up to 9
|
Analog Temp Inputs
|
Up to 3
|
Up to 3
|
Knock Control
|
2-Channel
|
2-Channel
|
On Board Wideband Air/Fuel Controllers
|
1
|
1
|
Drive-By-Wire
|
Single
|
Single
|
H-Bridge Channels
|
1
|
1
|
High Side Outputs
|
1
|
1
|
Low Side Outputs
|
8
|
6
|
Low Side Outputs that can be PWM
|
5
|
3
|
4-Wire Stepper Motor Control
|
Yes
|
Yes
|
CAN Channels
|
2
|
2
|
RS232 Channels*
|
1
|
1
|
Boost Control (RPM, Time, Gear, VSS, Switch Input, Flex Fuel Content)
|
Yes
|
Yes
|
Variable Cam Control
|
Up to 2
|
Up to 2
|
Engine Protection**
|
Yes
|
Yes
|
Launch Control
|
Yes
|
Yes
|
Nitrous Control
|
Single Stage
|
Single Stage
|
Traction Control
|
Up to 2-Wheel Speed
|
Up to 2-Wheel Speed
|
Data Logging
|
Up to 64GB
|
Up to 64GB
|
Weather Resistant Sealed Electronics
|
Yes
|
Yes
|
Connector Pins
|
80
|
80
|
Enclosure Dimensions
|
5.85" x 5.55" x 1.8"
|
5.85" x 5.55" x 1.8"
|
Weight
|
16.8oz / 476.27g
|
16.8oz / 476.27g
|
* Dual use pins. Tx and Tx shared with 2 digital inputs. DOES NOT OUTPUT AEM SERIAL DATA.
** Engine protection is programmable and can be coolant temp-, oil temp-, oil pressure-, AFR vs MAP, intake air temp-, knock- or fuel pressure-based